![]() It looks like it is not as long/wide as the original, so I don't know if it will properly reach and seal, but it is all I've found. I haven't tried replacing it yet because I'm having trouble getting the old one out, so I don't know if it works. It comes in a tightly wound coil of 36" inside a small blister pack. It is made by and the UPC is 0 49793 06230 7. I found a very similar replacement black bottom seal with a 5/23" half-round on the upper edge, at Menards. I have the same problem too, almost exactly like shown in the picture. Perhaps it's outdated? My husband is going to buy something similar and cut it to size. I have searched a lot and haven't found any company that sells this. Home Depot no longer carries the bottom sweep. According to pictures on web, it looks like American Standard shower door. And of course the replacement rubber strip and a couple of clamps, about 5 inch ones I know it sounds like a big procedure but it really isn't too bad as long as you can get the strip off and the screws loosened. The Goo Gone, a bottle of alcohol, a scraper, a screwdriver, a tube of clear silicone for bathrooms (I got the one that dries in 3 hours but you should wait 24 hours to use shower). Make sure you have the piece lined up with the correct sides before you glue it back on.Then I used clamps to hold the piece on while the silicone was drying. Then I used clear silicone to reattach the metal piece to the bottom of the shower door. Make sure you have gotten all the Goo Gone residue off with alcohol. Then I cleaned up the edge of the metal piece once more with alcohol and same with the metal where it was to be reattached. You cut off any extra rubber after you get the new piece in. I also asked the clerk to see if he could remove the other screw for me and he did. You just want to make sure the rubber is the right width and fits in the groove. So I took the whole piece to Home Depot and Lowe's (first one I went to they gave me the wrong kind of rubber strip) They carried a few different kinds of the rubber strips, so the guy looked at it and determined which one would fit into the groove when the old rubber was removed. I was able to loosen the screw on one end but not the other. On the ends of the metal piece was a screw that held the rubber in place. Then I looked at how the rubber fit into the piece. Then I cleaned off the sticky residue on both metal surfaces with Goo Gone (residue remover you can get at a hardware store or craft store), using a scraper (old credit card or putty knife). You may have to pry it off with a screwdriver. It was just stuck on with some adhesive and came off pretty easily. What I did was get down there and pulled off the whole metal strip that holds the rubber. You can always cut off the excess later on.I had exactly this same problem with my shower door which looks just like yours. Always cut in excess so you are sure all sides are covered. Step 4 - Cut the New Door SealĬut the new door seal to the length and width of your door depending on where you will be putting your seal. Make sure to remove all grime and lime scale. Step 3 - Clean the Glass ScreenĬlean your glass screen with glass cleaner or a solution of water and vinegar. If so, you may use a knife to carefully detach the door seal from the door itself. Sometimes it will be more complicated than this. Sliding it towards the side will not work. The best way to do this is to pull it down and out. Make sure the space between the door and the wall is not too small or big for the seal to be bridged is not either too large or small for the seal. You can also take the old door seal to your local hardware store and get an exact match. ![]() Measure the thickness of the door so you can purchase the right size door seal. ![]() A shower door shoe is a plastic or rubber fitting attached at the bottom of the shower door and suctions as a door seal. Some people find it effective to use this shower door seal with a door sweep. When the door is closed, the glass door is pressed to this rubber strip, pushing water into the tray. When the shower door is closed, it seals in water, and when the door opens, the opening action of the doors wipes the moisture that is present by the doors.Īnother is the shower door threshold, which is a rubber strip that is stuck to the curb of the shower tray or adhered to the shower floor. One is a shower door sweep, also known as a door wipe. There are different types of shower door seals on the market. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |